Mr-Glass Sliding Glass & Patio Doors Nationwide | TruePane Windows & Doors

Mr-Glass Sliding Glass & Patio Doors in Hollywood: What to Know First

TruePane Windows & Doors provides independent Mr-Glass sliding glass and patio door repair, replacement, and installation throughout Hollywood, FL. Most Mr-Glass service calls are completed in a single visit, and we carry the hardware, rollers, and weatherstripping that Mr-Glass doors in South Broward actually need. We quote the work on paper before we touch a screw, and the price on that paper is the price you pay.

Call (863) 334-2933

If you own a Mr-Glass door that binds, leaks, or won’t lock, this page outlines what goes wrong, what it costs, and how we fix it. Call (863) 334-2933 for a free estimate, and a live person will answer.

How Mr-Glass Products Fail - and How We Fix Them

Mr-Glass doors in Hollywood see the same salt air and afternoon thunderstorms as every other brand, but each line has its own failure patterns. Here’s what we find most often:

• Mr-Glass 600 Series patio doors: rollers seize and flatten. The original nylon rollers in the 600 Series were never built for the grit that blows across Hollywood Drive in July. When they flatten, the door rides metal-on-metal and the handle side drops. We replace the roller cartridges with aftermarket stainless-ball units that match the original track profile and bring the door back to square.
• Mr-Glass 7000 Series sliding glass doors: header deflection in west-facing walls. Afternoon sun on an unshaded west wall will push a 7000 Series header to sag, particularly on wider openings. The symptom is a door that slides fine until about two feet from the jamb, then catches. We shim and re-level the roller track, and on doors over eight feet we recommend a center support bracket the factory never called for.
• Early Mr-Glass HPG (impact) frames: weep gaps that did not age well. The original weep channels on early HPG frames were cut narrow, and ten years of Hollywood pollen and salt film will clog them solid. Water then ponds in the track and works its way under the sill. The fix is boring the weeps to spec and reinstalling the sill cap with proper slope.
• Mr-Glass sliding door handles and mortise locks: strikers that drift. Repeated door slam and frame settlement will carry the striker plate an eighth of an inch out of place. The door still locks, but there is play, and the play turns into a bind. We reset the striker, replace the mortise if the internals are chewed, and test the lock with the door both open and closed.
• Mr-Glass patio door glass: seal failure at the corner glazing channels. This shows up as a fog line and a vinegar-white film inside the glass. Here’s what Mr-Glass’s own warranty documents will not tell you: the seal fails because moisture wicks into the corner when the frame drain is blocked. We repair the leak path before we replace the insulated unit, otherwise the new pane fails the same way in three seasons.

Our Mr-Glass Sliding Glass & Patio Doors Process

1. 1
   Call and describe the symptom. A live person answers, 24/7. We’ll ask whether the door binds, leaks, or will not lock, and what it sounds like when it moves.
2. 2
   We show up, measure, and inspect. Every opening is measured twice before any talk of parts. We check the header, the track, the rollers, and the seal condition before we quote.
3. 3
   Parts decision on paper. We quote Mr-Glass OEM hardware where it makes sense, and quality aftermarket where the OEM part is the reason the door failed in the first place. You see both lines on the quote, side by side, with the price.
4. 4
   The repair or replacement. Rollers, track alignment, weatherstripping, sill caps, lock reset, or full door replacement if the frame is beyond square. Most jobs finish in one visit.
5. 5
   Test and register. We run the door through its full travel, check the lock, check the seal, and register every applicable warranty layer in writing before the truck leaves the driveway.
6. 6
   Cleanup and the Done Right Promise. The work area is left cleaner than we found it, and if anything is not right, we come back and make it right. No paperwork fight.

What Mr-Glass Sliding Glass & Patio Doors Costs in Hollywood

Pricing depends on the door model, the failure, and whether parts are OEM or aftermarket. These are the ranges we quote most often in Hollywood and nearby areas:

• Roller cartridge replacement (single panel): $160-$280
• Track realignment and shim package: $140-$260
• Weatherstripping and sill cap reseal: $110-$230
• Mortise lock and striker reset: $120-$240
• Insulated glass unit replacement (sliding door): $380-$680 depending on size and tint
• Full Mr-Glass sliding door replacement, installed: $1,200-$2,800 depending on frame width, impact rating, and glass package

What moves the price is the condition of the frame once we open it up, and whether the original install was square. We give a line-item quote before any work begins, and that quote does not change while the job is in progress. Call (863) 334-2933 for a free estimate on your specific door.

Why Hollywood Homeowners Call TruePane Windows & Doors for Mr-Glass Work

We have served local communities since 2008, and the owner, Dale Kessler, grew up in the Liberia neighborhood of Hollywood, where his father spent weekends resealing jalousie frames against the Atlantic. That history is why we treat every Mr-Glass door as a repair we are making for a neighbor, not a number for the quarter. Our technicians are background-checked, uniformed, and trained to work in your home the way they would work in their own mother’s.

Every job carries the Done Right Promise. If it is not done right, we make it right. We are also an authorized installer for more than a dozen manufacturer lines, including PGT, CGI, CWS, and ES Windows, so when a Mr-Glass door is not worth repairing, we can quote a replacement from a manufacturer that fits the same opening and performs better in Hollywood’s climate. Measure it right, set it square, and the paperwork takes care of itself.

FAQs