Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterMarvin Window Installation in Hollywood: What to Know First
Marvin window installation in Hollywood typically runs $95 to $165 per window for a straightforward insert install on ground-floor openings, with full tear-out replacements on older Hollywood homes landing between $650 and $1,100 per window. We’re an independent Marvin service provider, not a factory store, so we quote the work honestly and register both warranty layers in writing before we leave your driveway. If you own a Marvin window or door that needs proper installation, call us at (863) 334-2933 and we’ll measure it right the first time.
This page is for homeowners in Hollywood who already bought Marvin, or are planning to, and want the installation done by someone who treats the rough opening like it matters. Not someone who slaps a window in and disappears.
How Marvin Products Fail - and How We Fix Them
- Ultimate Casement windows binding at the operator arm. In Hollywood’s salt air, the galvanized hardware on Marvin Ultimate casements develops a light surface corrosion within three to five years. The arm doesn’t fail outright, but it starts dragging, and homeowners crank harder until the gear strips. We replace the operator assembly with the correct stain-grade hardware, not a generic crank from a parts bin, then reset the sash so it closes square. That’s the fix. A new handle alone won’t do it.
- Elevate and Essential double hungs losing their balance shoes. Marvin’s Elevate line uses a block-and-tackle balance system that is frankly better than most, but when the shoe snaps, the sash drops hard. We see this on Hollywood houses where windows get opened every morning and closed every night for years. We pull both sashes, swap the balance shoes as a pair (never one side only), and reset the tilt latches. If the window is under factory warranty, we register the repair through the approved channel so it costs you nothing.
- Signature wooden frames sponging at the bottom corners. Marvin Signature windows are gorgeous, but wood and Hollywood humidity are not always friends. When weep holes get blocked by salt film and old insect nests, water sits against the lower sash pocket and the wood softens. We clean the weep system, treat the affected wood with a wood consolidant, and if the rot has passed the sill, we recommend a full replacement rather than a patch that will fail in two seasons.
- Missing interior glazing stops on Clad Ultimates. After a previous installer has been through, we routinely find Marvin Clad Ultimate windows with interior glazing stops pried off and never properly re-seated. The glass sits loose, the window rattles in Hollywood’s afternoon storms, and the owner assumes the window is defective. It isn’t. We re-bed the glass on fresh glazing tape and snap the stops back with the factory-azimuth clips. The rattle stops the same day.
- Awning windows sagging at the hinge knuckle. Marvin awning units carry a lot of weight on two small stainless pivot points. Over a decade of salt exposure, those knuckles wear and the sash droops a fraction of an inch, enough to tear the weatherstripping at the top. We replace the hinge carriers with Marvin-compatible stainless hardware, adjust the keeper, and the seal comes back tight. No amount of cleaning will fix a worn hinge knuckle.
Our Marvin Window Installation Process
- 1
Measure the rough opening twice. We measure the actual opening, not the old window. Then we check level and plumb on all four sides with a laser, because a rough opening that’s out of square by three-eighths of an inch dictates how we set the new unit.
- 2
Pull the old window and inspect the framing. This is where we find the rot, the carpenter ant galleries, the shims some guy stuffed in from a job twenty years ago. We fix the opening before anything new goes in.
- 3
Choose OEM or quality aftermarket parts with you. For anything where warranty registration is in play, we use Marvin-spec parts and the factory installation methods. For out-of-warranty hardware, we can offer quality aftermarket options and show you the difference on paper.
- 4
Set the new window and flash it properly. We use butyl flashing tape and sloped sill pans on every opening, not just the ones on the second floor. Hollywood rain drives sideways. The flashing matters more than the window.
- 5
Insulate the perimeter with low-expansion foam, trim the window, and seal. We don’t leave fiberglass packed in behind the jamb extensions. Air moves right through fiberglass.
- 6
Test the operation, register the warranty, and walk you through it. Your Marvin warranty gets registered in writing, both manufacturer layers, before the truck leaves your driveway. Then we hand you the paperwork and make sure you know which number to call if anything acts up.
What Marvin Window Installation Costs in Hollywood
Here’s where the money goes on a typical Marvin job in Hollywood:
- Insert install, one ground-floor window: $95 to $165 per window, basic labor only
- Full tear-out replacement (wood framing repair included): $650 to $1,100 per window
- Top-floor or scaffolding jobs: add $150 to $300 per window for ladder safety and equipment
- Hardware replacement (operator, balance, lock, hinge): $85 to $240 per window, parts and labor
- Concrete or stucco surrounding repair after old window removal: $180 to $400 per opening
What moves the price is the condition of the rough opening. A clean opening with dry framing goes fast and costs less. A Hollywood house from the 1960s with rotten sills and out-of-square rough openings takes longer. We quote it after we measure, and the price doesn’t change once work starts unless you add scope. That’s the square deal. Call (863) 334-2933 for a free estimate.
Why Hollywood Homeowners Call TruePane Windows & Doors for Marvin Work
We’ve been in South Broward going on three decades, and Dale Kessler grew up in Hollywood’s Liberia neighborhood, resealing jalousie frames with his father on weekends. We know what the Atlantic does to window hardware, and we know what a Marvin window should look like when it’s set right. Our techs measure every opening twice, quote manufacturer lines side by side on paper, and register both warranty layers before the truck leaves your driveway. If it’s not done right in the first 90 days, we make it right. No paperwork fights, no fine print. And if you’re also pricing Andersen, Pella, or PGT for another part of the house, we’ll put those numbers in front of you too so you can compare what you’re actually buying. One call, one honest answer.
FAQs
Yes, in most cases. Marvin’s warranty is written for professional installation using factory-spec methods, and a DIY install that leaks or fails will typically not be covered. We register both warranty layers in writing after every install, which is the part most contractors skip. Call (863) 334-2933 and we’ll make sure your warranty actually holds.
Most insert installs take one visit, usually 45 to 90 minutes per window depending on access. A full tear-out with framing repair can run two to three days. We’ll tell you the schedule before we start and we’ll be there when we say.
Yes, in the majority of cases. Marvin windows are built to allow glass replacement without pulling the frame, but you need the correct glazing stops and the right tape thickness. We stock the common Marvin glazing components for Hollywood’s most popular lines and can order anything unusual within days.
If the frame is solid, the sash is square, and the issue is hardware or glazing, repair is almost always the right call. If the wood is soft, the frame is racked, or the glass is failed in a unit that’s more than 25 years old, replacement usually makes more financial sense. We’ll show you the numbers both ways, on paper, and let you decide with the measurements in front of you.
We pull permits on full replacements whenever the city requires one, and we handle the inspection. For insert installs and hardware work, no permit is needed in Hollywood. We’ll tell you which category your job falls into before we start. Call (863) 334-2933 for an exact quote, and we’ll outline the permit picture on that first call.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Hollywood and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.