Marvin Window Replacement Nationwide | TruePane Windows & Doors

Marvin Window Replacement: The Hollywood Owner’s Guide

We stock and install Marvin-compatible replacement windows throughout Hollywood, with typical installed pricing running $850 to $2,400 per window depending on series, size, and whether you’re replacing glass, hardware, or the full sash and frame. Most single-unit replacements are completed in one visit, and yes, we carry Marvin parts on the truck, not in a catalog we’ll order from after you’ve waited a week.

Call (863) 334-2933

Here’s how most Hollywood homeowners find us: the window that opened fine for fifteen years suddenly doesn’t. A crank turns and nothing moves. A sash drops an inch when you unlock it. Condensation shows up between the panes that wiping won’t fix. You have a Marvin product that’s served you well, something specific has failed, and you want the part matched correctly and installed square, not an estimate for a full-house replacement you didn’t ask for.

Key Takeaways:

• We match Marvin parts by series, glass size, and hardware generation, not by “close enough.”
• Installed replacement pricing is given in writing before work starts, parts and labor separated.
• We’re an independent service provider, not affiliated with Marvin. We install and service their product lines alongside Andersen, Pella, and others.
• Every job carries the Done Right Promise: if it’s not right, we make it right, no paperwork fight.

Which Marvin Models This Applies To

The Marvin lines we replace and service most often in Hollywood are the Ultimate and Elevate series, with older Integrity units still showing up regularly in homes built in the 1990s and early 2000s. Each series uses different hardware generations and glass specifications, so the first thing we do is identify what you actually have before quoting anything.

Look at the corner of the glass or the frame edge for a laser-etched mark or a small metal tag. Marvin stamps series codes on the hardware and glass spacer. If that’s faded, we measure the visible glass and the sash profile, because an Ultimate double-hung from 2008 and an Elevate from 2018 may share rough dimensions but use incompatible balances and latches. For most Marvin units, OEM parts make sense when the window is under warranty or the part is series-specific, like the Ultimate’s cam lock assembly. For discontinued hardware or out-of-warranty balances, quality aftermarket equivalents from a manufacturer we’ve vetted often get you back to functioning for 40 to 50 percent less, and we’ll quote both side by side on paper so you see exactly what you’re choosing.

One compatibility gotcha we see in Hollywood specifically: older Marvin units near the coast often have corrosion-damaged hardware that looks like a failure but is actually a symptom of salt air. Replacing the balance without addressing the track condition on a waterfront property buys you eighteen months, not fifteen years. We’ll tell you that before you spend.

Signs Your Marvin Window Replacement Is Failing

• Fog between the glass panes. The seal on the insulated glass unit has failed, and Florida humidity has worked its way inside. Once the argon or krypton fill escapes and moisture gets in, the glass package needs replacement, not repair. In Hollywood’s humidity, a failed seal moves from faint haze to visible condensation within a season.
• The crank turns but the sash doesn’t move. On casement and awning units, the operator gear teeth strip over time, especially if the sash was forced open against a corroded hinge. The operator is replaceable as a part; the hinge may need to be too.
• The sash drops or won’t stay open. Double-hung balances wear out, particularly in Florida where constant temperature swings fatigue the spring tension. A balance that’s lost tension is a replacement item, and we replace both sides, even if one still feels fine, because uneven tension pulls the sash out of square.
• The lock doesn’t engage or the sash feels loose when closed. Worn cam locks and keepers on Marvin units allow air and water to work through the weatherstripping. This is a hardware replacement, but it should be checked for alignment, because a lock that was forced can damage the sash profile itself.
• Water staining on the interior sill or drywall below the window. This is the one to take seriously. The issue may be a failed glazing bead or worn weatherstripping, but it can also be an installation problem from the original build, where the rough opening was never flashed properly. In Hollywood’s driving-rain season, that leaks. We inspect the full assembly, not just the part you noticed.

Replacement Cost & What’s Included

Here’s the range we quote in Hollywood, parts and labor included:

• Insulated glass unit replacement: $350 to $950 per sash, depending on glass size and whether it’s standard clear, low-E, or impact-rated.
• Hardware replacement (crank operator, lock set, latch): $120 to $380 per window, including the part and the service call.
• Balance replacement (double-hung, both sides): $180 to $400 per window.
• Full sash replacement: $600 to $1,400, matched to the existing frame where the frame is sound.
• Full window replacement (frame and sash): $850 to $2,400, depending on series, size, and impact requirements.

A few things drive the range: whether your neighborhood requires impact-rated glazing (much of east Hollywood does, and your insurance paperwork likely expects it), whether the window is a standard size or a custom unit from the original build, and whether the frame is salvageable. We quote the part separately from the labor, in writing, before work starts. You see exactly what you’re paying for. The workmanship is covered for 90 days under the Done Right Promise, and both warranty layers - the manufacturer’s on the part and our workmanship guarantee - get registered in writing before we leave your driveway.

A note on pricing: anyone who quotes you a Marvin replacement over the phone without seeing the window is guessing. We’ll give you a square deal, but it comes after we measure.

DIY or Call Us?

Some jobs are worth doing yourself. Most Marvin part replacements aren’t one of them, and here’s the honest split. What you can safely check: whether the window is square in the opening, whether the track is clean, whether hardware is visibly broken or just loose. Tightening a loose screw on a crank handle is reasonable. Everything beyond that is where DIY goes wrong.

Here’s what we’ve walked into after a homeowner tried it first: a double-hung balance that was replaced with the wrong size, and the sash came out of the frame while they were attempting the swap. Balances are under tension, and the wrong part is more dangerous than the broken one. On casement windows, replacing a crank operator means disassembling the hinge assembly, and getting the geometry wrong binds the window permanently. On glass packages, setting a new IG unit requires the right glazing tape thickness, the right shims, and a sash that’s square to the frame, or the new glass fails within a year. And if the unit is impact-rated, the mounting method is part of the product’s rating. Getting it wrong is a problem your insurer will care about.

Dale Kessler grew up in the Liberia neighborhood of Hollywood, where his father spent weekends resealing jalousie frames against whatever the Atlantic decided to send. He’s been measuring, setting, and troubleshooting windows in South Broward for going on three decades. His rule on the whiteboard hasn’t changed: measure it right, set it square, and the paperwork takes care of itself.

If you’d rather not risk the sash in the flower bed, call us at (863) 334-2933 and we’ll take it from there.

FAQs