Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterSimonton Energy-Efficient Windows in Hollywood: What to Know First
We’re an independent Simonton service provider in Hollywood, FL, and we handle energy-efficient window repair and replacement for Simonton owners the way the work should be handled: measured twice, quoted on paper, and finished with both warranty layers registered in writing. Most Simonton energy-efficient jobs in Hollywood run from $145 for a straightforward sash or seal repair up to $900-$1,400 for full replacement of a large Low-E insulated glass unit, and we typically complete the work in a single visit. If you’re holding a fogged Simonton unit or watching your AC bill climb through windows that don’t perform the way they did twenty years ago, call (863) 334-2933 and we’ll give you a straight answer before we touch a wrench.
How Simonton Products Fail - and How We Fix Them
Simonton builds a solid, mid-to-upper-range vinyl window, but in Hollywood’s heat and salt air, every window line has its own set of weak points. Here’s what we see most often, by series, and what we do about it.
- Simonton ProFinish / Asure Series - seal failure at the glazing bead. These two lines share a similar vinyl-glazed sash design where the adhesive-backed glazing tape eventually dries and shrinks in South Florida’s humidity cycle. The symptom is condensation between the panes that comes and goes with the weather. Most “fogged window” calls on these series aren’t actually a failed IGU; they’re a failed glazing seal that lets outside air hit the spacer. We pull the sash, replace the glazing tape with a marine-grade butyl, and re-set the unit square. If the IGU itself has actually failed, we order a replacement to spec and re-glaze it in the same visit.
- Simonton Reflections 5050 / 5500 - sash sag and weatherstripping compression. The 5050 and 5500 are good double-hungs, but after fifteen or twenty Hollywood summers, the spiral balance tubes wear and the sash starts to drift a few degrees out of square. When that happens the compression weatherstripping on the meeting rail gets crushed, and you lose the air seal that makes the window energy-efficient in the first place. We replace the balances as a pair, re-check the sash for square, and swap the weatherstripping for a fresh OEM-equivalent pile and fin seal. The window shuts like it did new, and the draft goes away.
- Simonton StormBreaker Plus - frame twist on impact units. These are impact-rated windows, and they’re heavy. On some Hollywood installs we’ve seen from other crews, the rough opening wasn’t shimmed at the corners, and over time the frame takes a slight twist. The window still closes, but it doesn’t seal evenly, and the energy performance drops because the weatherstripping can’t do its job across a warped plane. We pull the unit, correct the shims, re-set the frame square to the rough opening, and re-anchor it to code. That’s a full re-install, and it’s the only honest fix for a twisted frame.
- Simonton VantagePointe - failed Intercept spacer at the IGU. The VantagePointe line was marketed as Simonton’s energy-efficient floor, and in Hollywood’s UV load those Intercept spacers give out sooner than they do up north. The tell is a milky haze that starts at the bottom corners and creeps inward. That’s not cleanable, and it’s not caulk. It’s a true IGU failure, and the correct repair is a new double-pane unit with a stainless steel or warm-edge spacer, not another aluminum Intercept that will fog again in eight years. We order the replacement glass from a local fabricator, set it square in the existing frame, and register the new unit.
- Low-E coating degradation on south-facing Simonton units. Here’s a Hollywood-specific failure that doesn’t show up in Simonton literature: houses facing the lake or the Intracoastal get a double dose of reflected UV, and after twelve to fifteen years, the Low-E coating on south-facing windows can start to look hazy or slightly iridescent at certain angles. The glass is still insulating, but the coating is degrading. If the frame and hardware are otherwise solid, we replace the IGU with a higher-solar-gain Low-E package that’s actually correct for that elevation’s heat load, not just a default spec. Most window companies order the same glass for every side of the house. We don’t.
Our Simonton Energy-Efficient Windows Process
We don’t promise magic. We follow a process, and it works because we don’t skip steps.
- 1
Call and talk to a person. You call (863) 334-2933 and a live person answers, 24 hours a day. You describe the window, the symptoms, and the age of the house. We ask about the window’s location and whether you know the Simonton series. If you have the original paperwork, great. If not, we read the etched corner code on the glass when we arrive.
- 2
On-site measurement and diagnostic. A background-checked, uniformed technician arrives on schedule. We measure the rough opening, check the frame for square, inspect the sash hardware, and verify the failure before we quote anything. Dale Kessler has been reading rough openings since he was in the building construction technology program at Broward College, and the rule holds: measure it right, set it square, and the paperwork takes care of itself.
- 3
Side-by-side quote on paper. We show you OEM Simonton pricing and a quality aftermarket option where one exists, with line items for glass, hardware, labor, and any permit work. No ballpark figures. No “trust me.” You see exactly what you’re buying.
- 4
Repair or replacement, done in one visit. Most Simonton energy-efficient work is completed the same day: glass replacement, balance replacement, weatherstripping, re-glazing, or full unit replacement. If a custom-size IGU has to be fabricated, we schedule the follow-up before we leave, and we return on the date we set.
- 5
Test and verify airtightness. After the repair, we close and lock the window, check for even compression on all four sides, and verify the seal with a smoke pencil on high-draft walls. If the pane is not true, the job is not done.
- 6
Register both warranty layers before we leave. This is our Keystone Standard: the window goes back in the frame only after the manufacturer warranty and our Done Right Promise are registered in writing, with durations stated. You get a copy. We keep a copy. No paperwork fights later.
What Simonton Energy-Efficient Windows Costs in Hollywood
Here are straight numbers for the Simonton energy-efficient jobs we do most often in Hollywood. These are ranges from actual work, not brochure figures.
- Re-glaze a single-hung or double-hung sash (Asure, ProFinish, 5050): $145-$295 per sash, including new glazing tape and square re-set of the glass.
- Replace a failed Low-E IGU (double-pane, argon-filled): $450-$950 per unit, depending on size and glass package. A south-facing Hollywood window with strong UV exposure runs on the upper end.
- Full replacement window, energy-efficient double-pane, standard size: $900-$1,400 installed. Impact-rated Simonton StormBreaker Plus replacement runs higher, typically $1,500-$2,400, and requires a permit.
- Balance and weatherstripping restoration on a double-hung: $250-$500 per window. If one balance is worn, we replace both, always.
- Full-house energy audit with window-by-window ratings: $65-$120 for a standard Hollywood single-story, and we credit that amount toward any repair you schedule from the findings.
What moves the price is glass size, glass type, whether the frame gets re-set or replaced, and whether code requires an impact-rated unit in that opening. We don’t pad the bill and we don’t surprise you after the work starts. Call (863) 334-2933 and we’ll quote your exact windows on paper, free.
Why Hollywood Homeowners Call TruePane Windows & Doors for Simonton Work
TruePane has been serving South Broward since 2008, and Dale Kessler grew up in the Liberia neighborhood of Hollywood, where his father spent weekends resealing jalousie frames against whatever came off the Atlantic. We understand what salt air, 90-degree humidity, and afternoon thunderstorms do to a window frame, and we know Simonton’s products as well as any independent shop in the area. When a Simonton unit isn’t the right fix anymore, we can quote Andersen, Pella, PGT, or ViewLux side by side on paper, so you always know your options. Every job carries the Done Right Promise and The Keystone Standard, both warranty layers registered in writing before our truck leaves the driveway. And a live person answers every call, 24 hours a day, 7 days a week. We stand behind the work, in writing, for as long as we say we will.
FAQs
Simonton’s warranty coverage depends on the series, the year it was installed, and whether the warranty was ever registered or transferred. Most Simonton lines carry a limited lifetime warranty for the original purchaser, but it typically covers seal failure on a prorated basis after a set number of years, and it does not cover labor. If you don’t have the paperwork, we can often identify the series and age from the etched corner code and the rough opening dimensions, and we’ll tell you honestly whether a warranty claim is worth pursuing before you spend a dollar.
For hardware like balances, tilt latches, and weatherstripping, we can order Simonton OEM parts through our distributor network, and we quote them against quality aftermarket equivalents that are engineered to the same spec. For glass, we use local fabricators in South Florida who cut and seal double-pane units to exact dimensions with a stainless steel spacer instead of the aluminum Intercept that tends to fail early in Hollywood’s heat and UV. You see both prices on paper before you choose. Call (863) 334-2933 and we’ll walk through line items over the phone.
If the frame is square and the hardware works, replacing just the failed IGU almost always makes more sense than a full window replacement. A new double-pane Low-E unit in a solid Simonton frame costs roughly half what a full replacement runs and gets you back to the same energy performance. If the frame is twisted, the sashes sag, or the window is an older single-pane that can’t take double-pane glass, then replacement is the honest answer, and we’ll show you the numbers for both options on the same quote sheet.
No, and we want that up front. TruePane Windows & Doors is an independent Simonton service provider. We are not affiliated with or authorized by Simonton. What that means in practice is we don’t push a single brand, and we’ll tell you straight if a Simonton window is worth saving or if another line serves your Hollywood house better. It also means our Done Right Promise and The Keystone Standard are our own guarantees, in writing, not subject to a factory’s fine print.
Get Your Simonton Windows Done Right in Hollywood
If you’ve got a fogged unit, a draft that won’t quit, or a south-facing window that turns a bedroom into an oven every afternoon, call TruePane Windows & Doors at (863) 334-2933. We’ll have a technician at your Hollywood home when we say we’ll be there, we’ll measure everything twice, and we’ll put your options on paper with real pricing. Estimates are free, and the work carries the Done Right Promise, in writing. Done right, or we make it right. That’s the deal.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Hollywood and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.