Entry Doors

Entry Doors in Hollywood, FL | TruePane Windows & Doors

An entry door in Hollywood, FL does more than welcome people home. It is the first line of defense against wind-driven rain, flying debris, and the relentless coastal sun. TruePane Windows & Doors installs Therma-Tru fiberglass and steel entry door systems engineered for High-Velocity Hurricane Zone (HVHZ) performance, with the curb appeal that Hollywood homes demand, from Emerald Hills to Hollywood Lakes. These are not ordinary residential doors with a storm panel bolted on. They are complete, impact-rated entry systems tested as a unit, frame and slab together. For homeowners replacing a tired front door or builders finishing new construction, we handle the full install, done level, plumb, and square to AAMA 2400/2410 practice. Call (863) 334-2933 to schedule a free on-site measurement.

Call (863) 334-2933

Product Overview - Entry Doors

Florida entry doors fail in predictable ways. The sun warps hollow steel. Humidity swells wood. Storm season exposes every gap in the frame. The Therma-Tru impact entry doors we install in Hollywood are built to address all three problems at once, without forcing you to choose between a bunker and a beautiful front entrance.

You get a fiberglass or steel slab with a factory-set threshold and fully engineered frame system. Fiberglass won’t rot, warp, or rust. Steel brings maximum rigidity and a slimmer profile for homes with tighter rough openings. Both accept an impact-rated glass insert or work as a solid panel when you want zero glass exposure on a west-facing door. The factory-finished options arrive with a baked-on coating that will not peel like site-applied paint. Prefer to match a custom color? Paintable woodgrain finish gives you a genuine grain texture that takes and holds paint like wood, without wood’s maintenance demands.

In Hollywood, where architectural styles run from 1950s Florida ranch to contemporary coastal and Mediterranean revival, the right entry door changes the entire front elevation. We regularly specify these doors on Hollywood Lakes replacements where the original 1960s door has sagged past the point of weather-sealing, and on new builds near the Intracoastal where the permit reviewer specifically asks for HVHZ-rated door assemblies. The product line spans up to 48 inches wide, which covers most single-door openings in the area, including wider mid-century rough openings that a standard 36-inch box-store door cannot fill properly.

Technical Specifications

The spec table below reflects the configurations TruePane Windows & Doors quotes most often for Hollywood homes. Every door is ordered per opening, not pulled from stock, which is why we measure first and quote second.

• Frame materials: Fiberglass or steel, matched to the slab for consistent thermal movement
• Maximum width: Up to 48 inches, single panel
• Glass options: Decorative impact glass insert, Low-E insulated impact glass insert, or solid panel with no glass
• Finish options: White, black, bronze, or paintable woodgrain texture
• Impact configuration: HVHZ-rated slab and frame assembly, engineered as a complete system
• Sill: Thermally broken threshold designed for Florida rainfall exposure
• Hardware prep: Standard bore for entry hardware; we advise hardware selection during the quote so preps match your lock set

Hurricane & Compliance Performance

Six performance attributes matter when you price an entry door in Hollywood, and each one affects whether your permit is approved and whether the door holds when it counts.

Laminated Impact Glass
If your door carries a glass insert, it uses laminated impact glass with a PVB interlayer. The interlayer is what holds the glass in the frame even when a flying object shatters the outer pane. That means no gaping hole in your front door mid-storm, and no sudden pressurization of the house. Solid panel doors skip glass entirely for homeowners who want the simplest possible assembly.

Miami-Dade NOA / Florida Product Approval
Each configuration carries a Miami-Dade Notice of Acceptance and Florida Product Approval number. These are issued per specific door configuration, not as a blanket line rating. We verify the numbers on your quote against the exact size, glass, and finish combination you order. Your Hollywood permit reviewer will look for these numbers, and we provide them with the submittal package.

FBC / HVHZ Compliance
These doors are engineered to Florida Building Code High-Velocity Hurricane Zone requirements. HVHZ is the more demanding of Florida’s two wind provisions, and Hollywood sits squarely inside the HVHZ map. A door rated for the rest of Florida is not automatically legal here. This product line is specified for HVHZ jurisdictions like Broward County.

TAS 201 / 202 / 203 Testing Context
The HVHZ protocol family includes TAS 201 for large-missile impact, TAS 202 for cyclic wind-pressure loading, and TAS 203 for forced-entry resistance. These three tests simulate what a door actually endures in a named storm, repeated pressure cycles, and wind-driven abuse, not a single laboratory thump. When we say the door is HVHZ-rated, this is the test battery behind the claim.

Design Pressure for Your Wind Zone
We match design pressure to your specific wind zone, up to +/-100, never higher. Why “never higher”? Because over-specifying pressure ratings can drive cost without adding real performance for your location. A door on the beach in Hollywood faces different loads than one in a shaded inland lot near 441. The number on your quote reflects the actual requirement, not a showroom guess.

Energy Performance
The Low-E insulated glass insert option reflects solar heat before it enters your home and helps control interior temperatures year-round. Hollywood’s cooling season runs most of the year, so glass choice matters more than most homeowners expect. A solid panel door with a quality perimeter seal performs even better thermally, but you lose the daylight and curb appeal of a glass insert.

Color & Glass Options

Hollywood’s housing stock runs the full Florida palette, and the finish you pick should work with the whole elevation, not just the door.

White stays clean against pastel coastal homes and reads crisp on the classic Hollywood 1950s and 60s ranches. Black gives strong contrast on white stucco and works especially well on contemporary and Mediterranean-inspired facades, where dark frames are already common. Bronze blends into earthy tones and hides salt haze better than lighter colors on homes within a few blocks of the beach. The paintable woodgrain option exists for homeowners who want a specific custom color, like a deep navy front door to match shutters, or a color sampled directly from the HOA palette in neighborhoods with strict architectural review.

Glass selection follows function. A decorative impact glass insert brings light and pattern into a dark entry hall while still carrying the laminated impact construction. The Low-E insulated insert is the better choice when the door gets direct afternoon sun, which is most west-facing doors in Hollywood. A solid panel makes sense for doors with zero covered porch overhang, or for homeowners who simply want the strongest, most weathertight door with no glass to maintain.

Installation by TruePane Windows & Doors in Hollywood

A hurricane-rated entry door is only as good as the installation around it. The NOA and Florida Product Approval numbers assume the door is installed correctly. A sloppy install, a twisted frame, a skipped leveling step, and the tested assembly never performs the way the lab report says it will. We see this constantly in Hollywood: impact doors that are “rated” but leak at the threshold or bind after six months because the frame was shimmed wrong.

Our process starts before the door is ordered. We measure the actual rough opening, check the condition of the existing framing, and look for rot, termite damage, or out-of-square conditions that will affect the install. On older Hollywood homes, the rough opening has often shifted, and forcing a new door into it without correction is how you end up with a door that will not latch cleanly in August.

Installation follows AAMA 2400/2410 practice. We set the frame level, plumb, and square, then seal the perimeter with AAMA 812 low-expansion foam before finishing with the specified exterior sealant. The threshold gets bedded properly, not just set against raw concrete. We run a final water test on the sill and lower corners. Then we clean the job site. Hollywood construction debris accumulates fast, and we do not leave door packaging in your driveway.

Permitting is part of the job. Hollywood sits in an HVHZ jurisdiction, and the building department expects the NOA or Florida Product Approval documentation with the permit application. We provide the correct numbers for your exact configuration and support the submittal. If the review comes back with questions, we answer them. That is the difference between buying a door and buying a door system from a company that understands Broward County’s permit process.

Improper installation compromises the NOA-rated system. That is not marketing language; it is the reality of how these assemblies are tested and listed. If you are comparing quotes, ask every bidder how they shim and seal the frame. If the answer is vague, keep looking.

Frequently Asked Questions - Entry Doors

Get a Quote - Entry Doors in Hollywood

Every TruePane impact entry door installation in Hollywood starts with a free on-site measurement. We review the existing opening, check for framing conditions, confirm your wind zone, and give you a written line-item quote with the exact NOA or Florida Product Approval numbers for your configuration. No guesswork, no change-order surprises. Call (863) 334-2933 to schedule yours.

Written by the team at TruePane Windows & Doors, serving Hollywood, FL and surrounding Broward County communities with hurricane-impact window and door installations.